® is a non-toxic formula
® has been 3rd party certified by Ecologo to be environmentally safe (CCD 046 – General Adhesives).
® will dry clear and flexible and is therefore
ideal for use with woods and fabrics as no glue lines will show and the
glue will bend with movement. It is non-staining and will not become
brittle with age.
® has various applications and can be used
straight from the bottle as a glue or bonding agent or can be diluted
and used as a sealer or primer.
® is water soluble and can be cleaned up with
water within 20 minutes of application if drips appear. Get a warm, wet
cloth and apply to the area to remove drips. Weldbond does become water
resistant but not waterproof.
® will create a solid bond as it cures and requires no heavy clamping while drying.
® dries clear and can be painted over making it perfects for repairs and craft projects as you will not see the glue lines.
® can be diluted and used as a primer for bare drywall or other porous surfaces. Using Weldbond®
helps to seal the drywall and ensure that the paint is not absorbed
into the drywall but rather sits on top for a beautiful finish (any type
of paint can be applied overtop of Weldbond). Saves money and time.
® is not tested on animals and is not created with any animal by-products.
® is manufactured in North America.
® is weatherproof and can therefore be used for outdoor projects. However because Weldbond® is not waterproof avoid using Weldbond® where standing water collects as it will cause Weldbond® to freeze.
® is available in numerous sizes for various
applications and project needs. Bottles: 2oz/60 ml, 4 oz/114 ml, 8oz/227
ml, 12oz/341 ml, 21oz/600 ml, 64oz/1/2 gallon/1.82 litres, 128 oz./ 1
gallon Tubes: 1oz/30 ml, 5oz/150 ml, 9oz/275 ml
® should be protected from the cold as it will
freeze. Once frozen, this product loses all adhesive capabilities. It
should be stored above 50°F/ 10°C at all times. Also, after container
has been opened, ensure it is closed tightly after each use.
® typically has a shelf life of 5 years. If the
product is starting to solidify, it can be restored by adding just a
little bit of water. We then advise the consumer to shake like crazy
prior to every use until the container is depleted.
® has been tested to be non-toxic. Weldbond® conforms to ASTM D4236.
You can access the Weldbond
® MSDS via the Weldbond® website, click here.
You can also send us an email to
firstname.lastname@example.org requesting the document and we will forward you an electronic copy.
® is not tested on animals and does not contain any animal by-products. This product is Vegan Friendly.
EcoLogo™ certifies that Weldbond
® has been tested for
environmental safety and performance under CCD 046 – General Adhesives.
EcoLogo™ is a 3rd party certification seal that certifies products
based on strict standards. To read more about EcoLogo™,
A porous surface means that the material is full of tiny holes that
allow fluids or gases to pass through, non porous surfaces do not allow
anything to pass through.
Porous surfaces must be sealed with 1 part Weldbond
® to 5
parts water. Porous surfaces can be determined by dropping a small
amount of water on surface. If water is readily absorbed, surface is
porous. If water beads on the surface, it is non porous.
NOTE: The sealing mixture of 1 Weldbond® to 5 water should not be used where water alone would have an adverse effect, i.e. on water soluble fillers.
Some types of plastic, rubber and cast metals will not produce a bond with Weldbond
® , i.e. polyethylene, unbacked vinyl, P.V.C., Teflon®,
polypropylene, vinyl to vinyl, cast iron, cast aluminum. Weldbond® is
not intended for marine applications. It is not recommended for use on
exposed exterior surfaces. Garage interiors are acceptable.
NOTE: Do not use when bonding containers designed for use with, or subject to, hot liquids.
® is a water based glue therefore if the
stain/spill is recent we recommend using cold water, not hot water.
However once the glue has set it is very difficult to remove therefore
be sure not to wear your favourite clothes while using Weldbond
®, just in case!
® can quickly be dissolved with acetone. Because Weldbond® is water based it can also be dissolved with a soaking of, or submersion in water. This will dissolve a bond.
We have many craft users that tint Weldbond
® with a wide
variety of creative methods, including tea, paint, nail polish and other
creative methods. We always recommend the consumer to test this
creation on a small piece prior to proceeding with the full project.
Some compounds utilized for tinting could have an adverse impact on the
makeup of the Weldbond
We recommend Latex and Acrylic paints for the best results.
® can be used on external applications as it is weatherproof. However, Weldbond® is not waterproof, it is water resistant. Weldbond®
should only be used on external applications if it is free of standing
water that could cause it to freeze or if it is being used on a vertical
surface where water cannot pool on top.
® is not intended for marine applications. It is not recommended for use on exposed exterior surfaces.
a. Why not?
Most like too much adhesive was used. Another possibility could be
that if you are gluing a large surface, air cannot get to the Weldbond
in the middle of the bond. We do suggest that if you are gluing large
pieces, you apply the adhesive to the exterior rim and not the centre as
a proper bond might not take place.
b. What can I do about it?
Apply heat. If weather conditions permit, set the project in the
sun. For large glass surfaces, glue the edges, but stay away from large
amounts of glue through the middle of the surface. Weldbond
® air cures.
® does not release any fumes no matter if it is in liquid or solid state.
The set up time for tackiness will vary with humidity, but is roughly
five minutes for most projects. It will be somewhat longer in humid
® becomes tacky quickly and will dry within the
hour on porous surfaces. Provides a strong bond within 24 hours and
tremendous strength within a few days. The sealing mixture of 5 parts
water to 1 part concentrated Weldbond
® dries in approximately 1 hour.
For more information regarding specific gluing jobs, please check the Weldbond
® Application Uses section.
® is a PVA adhesive . (Poly Vinyl Acetate based adhesive)
® does not contain any formaldehyde preservative. The EcoLogo™ certification states that Weldbond®
has been created without: latex, aromatic or halogenated solvents,
formaldehyde, toxic metals, including but not limited to cadmium,
hexavalent chromium, lead, and mercury, or their compounds
® is created without the use of phthalates and is therefore free of phthalates.
® does not contain more than 1% VOCs by weight. This technical fact is approved and certified by EcoLogo™.
Built with Volusion