news + notes

Home > Designer Products >   Image Transfer Paper (Five 8.5"x11" Sheets)
Additional Photos:	ITS paper is a special product designed to be used with Image Transfer Solution. Our Price: $12.95 You'll earn 13 Rewards Points Product Code: 53209 Qty:

More Information Instructions   After applying your transfer and heat setting the image, the paper is easily removed in water(the paper dissolves). Very little sanding if any is necessary to reveal beautiful transparent images on oven proof surfaces. Use blank ITS paper to print your own laser images, or use the pre-printed images from our collection to add images to metal,polymer clay, or unglazed tile. Directions for using ITS PAPER with ITS onto metal, unglazed tile or polymer clay: 1. Cut out a pre-printed image to fit your surface (Laser copied images-toner based). The matte side of the paper is preferable for printing, although not critical. Hints: Use images with a high contrast and strong lines. It helps to test images on a surface such as a bottle cap prior to transferring to your final piece. 2. Brush an even coat of ITS on the surface of the metal, or other material (such as baked polymer clay). Don’t brush the layer too thin, it should be similar to a decoupage application. (If using metal that is highly polished then prepare the surface prior to working by sanding with 600 grit paper to add a “tooth” to the surface. 3. Press the image face down (printed side down) onto the wet ITS. Press the image down firmly to make sure it is in full contact with the surface. Wipe away excess ITS around the edges. (It’s important not to get the solution on the back of the paper as makes the paper harder to remove later). 4. Let the piece air dry overnight or speed the process by using a hair dryer for a few minutes. Bake the piece in an oven at 325° F for metal or tile (275° F for polymer clay) for 30 minutes to heat set. 5. After baking the piece soak the paper backing off in water for a minute or two. Use your fingernails or a 3M Scotch Brite No Scratch Scrub Sponge to remove the paper from the image. Finish by drying and buffing with a cloth to remove any remaining fibers; an old t-shirt, dish towel-(the flour sack type), or the knee of your denim jeans work well to buff the surface. 600 grit wet/dry sanding paper can also be used under running water to remove any remaining fibers around the edges of the image. Whisk the sand paper across gently, don’t scrub! 6. To refine the surface and bring up the color and sheen of the transfer, coat with a layer of Renaissance Wax using a soft cloth, or use varnish. ITS works as a sealer as well, simply brush on a layer of the solution and let it air dry (no heat setting required when used as a sealer). Image Transfer Solution Our Price: $14.95 Add Hadar's Clay - Quickfire Sample Pack Hatties Metal Clay Drying Mat HattieS QuikArt™ Ring Shanks - B Hadar's Clay - Quickfire Bronze Our Price: $42.50 Add Our Price: $2.30 Add Our Price: $8.49 Add Our Price: $13.20 Add PMC Basics Tim McCreight DVD Gordon Uyehara Triangle Bead QuikArt Template Stainless Steel Wire Cloth for Carbon Firing - 6" Hadar's Clay - Quickfire Pearl Grey Steel XT Sale Price: $21.69 Add Our Price: $8.49 Add Our Price: $5.95 Add Add

Share your knowledge of this product with other customers... Be the first to write a review

	ITS Colors™ Kit $39.95
	ITS Color Pigment - Replacement Vials
	Hex/Heart Component Mold Mary Ann Devos $16.90
	HattieS® Words of Inspriration Stamp $3.45
	HattieS® Sterling Earring Posts - PMC Ready (1 pair) $3.75
	HattieS® Ring Shank Guide™ $4.45
	HattieS® Rainbow Patina Kit $37.45

• Metal Clay Supply Rewards
• RSS Feed
• YouTube